Call Our Team for Well Pump Repair in Catawba, NC
Submersible & Jet Pump Repair Solutions
Dealing with no water, erratic pressure, or a pump that won't stop running is frustrating. However, it doesn't always mean your pump is toast.
A&B Plumbing offers well pump repair in Catawba, NC. We serve the area with a 'diagnose first' approach. We don't jump to pull the pump unless we know it's necessary. Often, the issue is something simpler and more affordable.
If it’s fixable, we’ll fix it. Our trucks are fully stocked with these common parts, allowing us to get you back to normal without the wait.
Give us a call today!
Signs Your Well Pump May Need Repair
Well systems often show symptoms before water service stops completely. A change in pressure or pump behavior should be investigated before the problem develops into a complete loss of water.
Common signs include:
No water from faucets even though the pump appears to be running
Sputtering fixtures or air bubbles in the water
Low water pressure throughout the house
A pump that runs continuously without shutting off
Significant pressure fluctuations between uses
Discolored or sandy water
A breaker that repeatedly trips when the pump operates
How We Diagnose Well Pump Problems
We do not start by pulling the pump. Pulling a submersible unit before testing the rest of the system can add unnecessary labor to a repair.
Our diagnostic process may include checking:
-
Water Pressure and Pump Cycling
We inspect the pressure tank and evaluate the system's cut-in and cut-out operation. Problems with cycling can point toward a pressure switch, tank issue, or other component failure.
Common residential pressure switches include Square D 30/50 and 40/60 models.
-
Wiring and Electrical Components
We test the wiring and related electrical components connected to the well system. Control boxes and capacitors can fail without the submersible pump motor itself being the problem.
-
Check Valve Operation
A failed check valve can allow water to flow back toward the well, causing pressure loss and abnormal cycling. In some cases, replacing a relatively inexpensive check valve resolves what initially appears to be a major pump problem.
-
The Pump and Motor
If the diagnostic points to the pump assembly itself, we can pull the submersible unit for further testing and inspection. This may include a megger test on the motor, continuity testing on the leads, inspection of the drop pipe, and a functional evaluation of related components.
Once the source of the failure is identified, we explain the repair before work begins.
Submersible Pump vs. Jet Pump
The type of pump installed on your property affects how we approach the repair.
Submersible Well Pumps
A submersible pump sits inside the well casing below the water level and pushes water toward the home. Most Catawba County homes with wells drilled after 1980 use this type of system.
From above ground, you may only see the wellhead and electrical wiring. The pump itself is located deep inside the well, so pulling it is a more involved process.
Submersible pumps commonly last between 10 and 25 years, depending on water conditions, cycling frequency, installation quality, and the equipment itself.
Jet Pumps
Jet pumps are installed above ground and pull water from the well. They are commonly associated with shallow wells, often under approximately 25 feet, along with some older residential installations around Lake Hickory.
The pump and pressure tank are generally visible in a basement, garage, utility room, or dedicated pump area.
If you are unsure which system you have, we can identify the equipment during the diagnostic.
Repair Before Replacement
A complete pump replacement is sometimes necessary. A failed pressure switch or check valve does not justify replacing a functioning pump.
That is why we test the accessible components before recommending that the pump be pulled. In some cases, the repair may involve a pressure switch that costs around $90 or a check valve that costs around $40. A full submersible pump replacement is a much larger project.
Well Pump Brands We Service
We work on many of the well pump brands found throughout Catawba County, including:
Grundfos SQE constant-pressure systems can reduce short cycling, which may contribute to longer equipment life when compared with systems that cycle more aggressively.
We also stock common Franklin Electric control boxes, capacitors, Square D pressure switches, and check valves on our trucks.
Well Pump Repair for Catawba and Surrounding Areas
A&B Plumbing provides well pump repair services throughout communities where private well systems are common.
Our service area includes:
-
CONOVER
-
MAIDEN
We regularly serve properties in ZIP codes including 28601, 28602, 28609, 28610, 28613, and 28658.
Frequently Asked Questions
A submersible pump typically lasts between 10 and 25 years. High sediment or iron content can contribute to equipment wear. Pump cycling also affects service life.
No. Many well system problems can be identified without pulling a submersible pump. We check pressure, controls, electrical components, and other accessible parts first.
Yes, depending on the failed component. A pressure switch, check valve, control box, capacitor, or electrical component may be repairable without replacing the pump assembly.
Get Help from The Well Pump Repair Experts
If your home has lost water pressure or your faucets have stopped producing water, contact A&B Plumbing for well pump repair in Catawba, NC.
We provide diagnostic and repair services for submersible and jet well pump systems throughout Catawba County. Let us find and fix any failed component before recommending major equipment replacement.
Call A&B Plumbing at (980) 276-0199 to schedule a service.
